## ## === When you're using remote logging, enable on-disk queues === ## === in rsyslog.d/remote.conf. === ## ## Note, that when the MYSQL, PGSQL, GSSAPI, GnuTLS or SNMP modules ## (provided in separate rsyslog-module-* packages) are enabled, the ## configuration can't be used on a system with /usr on a remote ## filesystem, except on newer systems where initrd mounts /usr. ## [The modules are linked against libraries installed bellow of ## /usr thus also installed in /usr/lib*/rsyslog because of this.] ## # ######### Enable On-Disk queues for remote logging ########## # # An on-disk queue is created for this action. If the remote host is # down, messages are spooled to disk and sent when it is up again. # #$WorkDirectory RSYSLOG_SPOOL_DIR # where to place spool files #$ActionQueueFileName uniqName # unique name prefix for spool files #$ActionQueueMaxDiskSpace 1g # 1gb space limit (use as much as possible) #$ActionQueueSaveOnShutdown on # save messages to disk on shutdown #$ActionQueueType LinkedList # run asynchronously #$ActionResumeRetryCount -1 # infinite retries if host is down # ######### Sending Messages to Remote Hosts ########## # Remote Logging using TCP for reliable delivery # remote host is: name/ip:port, e.g. 192.168.0.1:514, port optional #*.* @@remote-host # Remote Logging using UDP # remote host is: name/ip:port, e.g. 192.168.0.1:514, port optional #*.* @remote-host # ######### Receiving Messages from Remote Hosts ########## # TCP Syslog Server: # provides TCP syslog reception and GSS-API (if compiled to support it) #$ModLoad imtcp.so # load module #$Address 10.10.0.1 # force to listen on this IP only #$Port # Starts a TCP server on selected port # Legacy configuration parameters that should not be used when crafting new configuration files. ##$UDPServerAddress 10.10.0.1 # force to listen on this IP only #$InputTCPServerRun # Starts a TCP server on selected port # UDP Syslog Server: #$ModLoad imudp.so # provides UDP syslog reception #$Adress 10.10.0.1 # force to listen on this IP only #$Port 514 # start a UDP syslog server at standard port 514 # Legacy configuration parameters that should not be used when crafting new configuration files. #$UDPServerAddress 10.10.0.1 # force to listen on this IP only #$UDPServerRun 514 # start a UDP syslog server at standard port 514 ########### Encrypting Syslog Traffic with TLS ########## # -- TLS Syslog Server: ## make gtls driver the default #$DefaultNetstreamDriver gtls # ## certificate files #$DefaultNetstreamDriverCAFile ETC_RSYSLOG_D_DIR/ca.pem #$DefaultNetstreamDriverCertFile ETC_RSYSLOG_D_DIR/server_cert.pem #$DefaultNetstreamDriverKeyFile ETC_RSYSLOG_D_DIR/server_key.pem # #$ModLoad imtcp # load TCP listener # #$InputTCPServerStreamDriverMode 1 # run driver in TLS-only mode #$InputTCPServerStreamDriverAuthMode anon # client is NOT authenticated #$InputTCPServerRun 10514 # start up listener at port 10514 # # -- TLS Syslog Client: ## certificate files - just CA for a client #$DefaultNetstreamDriverCAFile ETC_RSYSLOG_D_DIR/ca.pem # ## set up the action #$DefaultNetstreamDriver gtls # use gtls netstream driver #$ActionSendStreamDriverMode 1 # require TLS for the connection #$ActionSendStreamDriverAuthMode anon # server is NOT authenticated #*.* @@(o)server.example.net:10514 # send (all) messages